PRODUCTS- 產品介紹 -

WISE-7517M-10

WISE-7517M-10
WISE-7517M-10
WISE-7517M-10

產品型錄(PDF)

操作手冊(PDF)
 

產品介紹

WISE (Web Inside, Smart Engine) 為泓格科技所開發；具備自主邏輯控制與遠端監控通知等多項功能的智慧型控制器。在此系統下，使用者不再困擾於控制器中邏輯程式的撰寫，而僅需透過 WISE 所提供的網頁人機介面及滑鼠點選動作，即可完成控制器上工作邏輯的規劃，過程簡單且快速，其可大幅降低使用者在系統開發上的資源花費。

WISE-7517M-10 遵照 IEEE 802.3af 標準 (classification, Class 1) 中的 Power over Ethernet (PoE) 規範，可在 PoE 網路環境下透過網路線 (Category 5) 傳送電力。此功能提供了更大的靈活性及效率以簡化系統設計、節省空間並減少電線及電源插座的需求。此外，WISE-7517M-10 內建雙乙太網口 (Two-port Ethernet switch)，不需透過交換機 (Switch) 即可直接進行最多10個模組的串接。讓現場佈線更加方便。

WISE-7517M-10 提供 10/20 組 AI 通道。透過內建的 IF-THEN-ELSE 邏輯規則執行引擎，WISE-7517M-10 可提供 I/O 通道監控、計時器/排程時序控制、E-mail/CGI 命令發送等功能，可運用於自動化監控應用中。此外，WISE-7517M-10 同時支援 Modbus TCP 及 MQTT 通訊協定，可與 SCADA、IoT 系統進行無縫整合。

產品特色

  • 內建網頁伺服器，無須安裝軟體工具
  • 無須撰寫程式，僅需要點選即可完成規則編輯
  • 內建 IF-THEN-ELSE 的邏輯運算引擎
  • 內建 I/O 通道 (10/20 組 AI 通道)
  • 支援 IO 通道監控、計數器、計時器、排程、Email 發送、CGI 命令發送等指令
  • 透過 Modbus TCP 與 SCADA 系統進行無縫整合
  • IEEE 802.3af 標準 Power over Ethernet (PoE)
  • 內建雙乙太網口 (Two-port Ethernet switch)，提供 Daisy-Chain 方式連接
  • 透過 MQTT 協定與 IT 及物聯網 (IoT) 系統進行無縫整合

產品應用

自動化建築、自動化工廠、自動化機械、遠端維護、遠端診斷及測試設備等。

硬體規格

Analog Input
Channels 10 differential or 20 single-ended (Note1), software selectable
Type ±150 mV, ±500 mV, ±1 V, ±5 V, ±10 V 
±20 mA ,0 ~ 20 mA, 4 ~ 20 mA (Jumper Selectable)
Resolution 16-bit
Sampling Rate 10 Samples/Second (Total)
Accuracy ±0.1 %
Zero Drift ±20 μV/°C
Span Drift ±25 ppm/°C
Overvoltage Protection Differential 240 Vrms
Single-ended 150 Vrms
Common Voltage Protection ±200 VDC
Overcurrent Protection Yes, 50 mA at 110 VDC
Virtual Channel to Channel Isolation Yes, 400 VDC
Open Wire Detection for 4 ~ 20 mA Yes
Input Impedance Voltage 2 MΩ (Differential), 1 MΩ (Single-ended)
Current 125 Ω
Common Mode Rejection 86 dB Min.
Normal Mode Rejection 100 dB
Note1:  Differential mode can be used for voltage input and current input.
   Single-Ended mode can be used for voltage input only.
Communication
Ethernet Port 2 x RJ-45, 10/100 Base-TX, Swtich Ports
PoE Yes
Protocol Modbus TCP, MQTT
LED Indicators
for System Running Yes
for Ethernet Link/Act Yes
for I/O Channel Status Yes
for PoE Power Yes 
2-Way Isolation
I/O 2500 VDC
EMS Protection
ESD (IEC 61000-4-2) ±4 kV Contact for Each Terminal and 
±8 kV Air for Random Point
EFT (IEC 61000-4-4) ±2 kV for Power Line
Surge (IEC 61000-4-5) ±2 kV for Power Line
Power
Reverse Polarity Protection Yes
Powered from Terminal Block 12 ~ 48 VDC
Powered from PoE Yes, IEEE 802.3af, Class1
Consumption 3.7 W (Max.)
Mechanical
Dimensions (L x W x H) 120mm x 97mm x 42mm
Installation Wall mounting
Environment
Operating Temperature -25 °C to +75 °C
Storage Temperature -30 °C to +80 °C
Humidity 10 to 90% RH, non-condensing

軟體規格

Functions
Rule Configuration Website Access Web server on WISE controllers to edit and upload logic rules through web browser.
72 IF-THEN-ELSE Logic Rules 3 IF conditions with AND or OR operators
3 THEN actions and 3 ELSE actions
48 Internal Registers Hold temporary variables and read/write data
24 Timers Delay / Timing functions.
24 Schedules Setup prescheduled routine tasks.
24 Emails Send Email messages to pre-set Email receivers.
24 CGI Commands Send pre-set CGI commands.
24 Recipes Set up THEN/ELSE action groups.
8 P2P remote modules Set up the connection information for the remote WISE modules.
Modbus TCP Protocol Real time control and monitoring I/O channels and system status of controllers via SCADA software.
MQTT Protocol Real time message publish/subscribe mechanism for I/O channels and system status via IT/IoT software.
IF Conditions
AI Channel = 、> 、< 、 ≥ 、 ≤ (value)
Internal Register
Timer Timeout, Not Timeout
Schedule In Range, Out of Range
P2P DI, AI, DI counter, DO counter, IR
Rule Status Enable, Disable
THEN / ELSE Actions
Internal Register Change the value
Timer Start, Reset
Schedule Enable, Disable
Email Send
MQTT message
CGI Commands
Recipe Execute
P2P DO(On/Off), AO, IR
Rule Status Enable, Disable
Back List