| 
 
 產品型錄(PDF)
 
 
 
 
 
  | 
		
			| 
				
					
						| Models | I-7017Z | M-7017Z |  
						| Analog Input |  
						| Channels | 10/20 |  
						| Wiring | 10 Differential or 20 Single-ended (Software Selectable - see Note 1) |  
						| Sensor Types | Voltage | ±150 mV, ±500 mV, ±1 V, ±5 V, ±10 V |  
						| Current | ±20 mA , 0 ~ +20 mA, +4 ~ +20 mA (Jumper Selectable) |  
						| Resolution | 16-bit |  
						| Accuracy | Normal Mode | ±0.1% of FSR |  
						| Fast Mode | ±0.5% of FSR |  
						| Sampling Rate | Normal Mode | 10 Hz |  
						| Fast Mode | 60 Hz |  
						| Input Impedance | Voltage | 2 MΩ (Differential) |  
						| 1 MΩ (Single-ended) |  
						| Current | 125 Ω (Differential) |  
						| Common Voltage Protection | ±200 VDC |  
						| Individual Channel Configuration | Yes |  
						| Overvoltage Protection | 240 Vrms |  
						| Overcurrent Protection | Yes, 50 mA at 110 VDC |  
						| Temperature Output Consistency | Yes, 400 VDC |  
						| Open Wire Detection for +4 ~ +20 mA | Yes |  | 
		
			| Note 1: Differential wiring can be used for both voltage input and current input. Single-ended wiring can only be used for voltage input
 | 
		
			|  | 
		
			|  | 
		
			| 
				
					
						| Models | I-7017Z | M-7017Z |  
						| Communication |  
						| Interface | RS-485 |  
						| Bias Resistor | No (Usually supplied by the RS-485 Master. Alternatively, add a tM-SG4 or SG-785.) |  
						| Format | N, 8, 1 |  
						| Baud Rate | 1200 to 115200 bps |  
						| Protocol | DCON | Modbus RTU, DCON |  
						| Dual Watchdog | Yes, Module (1.6 Seconds), Communication (Programmable) |  
						| LED Indicator/Display |  
						| System LED Indicator | Yes, 1 as Power/Communication Indicator |  
						| I/O LED Indicator | - |  
						| 7-Segment LED Display | - |  
						| Isolation |  
						| Intra-Module Isolation, Field-to-Logic | 3000 VDC |  
						| EMS Protection |  
						| ESD (IEC 61000-4-2) | ±4 kV Contact for each Terminal |  
						| EFT (IEC 61000-4-4) | ±4 kV for Power Line |  
						| Surge (IEC 61000-4-5) | ±0.5 kV for Power Line |  
						| Power |  
						| Reverse Polarity Protection | Yes |  
						| Input Range | +10 ~ +30 VDC |  
						| Consumption | 2.0 W |  
						| Mechanical |  
						| Dimensions (L x W x H) | 123 mm x 72 mm x 35 mm |  
						| Installation | DIN-Rail or Wall Mounting |  
						| Environment |  
						| Operating Temperature | -25 to +75°C |  
						| Storage Temperature | -40 to +85°C |  
						| Humidity | 10 to 95% RH, Non-condensing |  |